Most sellers know that furniture has to arrive in one piece. Fewer know that a plain bedroom dresser, a particleboard bookcase and an upholstered armchair each sit under a different federal rule, written by a different agency, with its own test, its own label and its own paperwork. Miss one and the product can be pulled from sale, however well it photographs.
This guide covers three rules that catch flat-pack and furniture resellers out: the tip-over standard for clothing storage units from the Consumer Product Safety Commission (CPSC), the formaldehyde emission rules for composite wood from the Environmental Protection Agency (EPA), and the flammability rules for upholstered furniture, which now exist at both the federal level and in California. It explains who each rule is aimed at, what the label or paperwork looks like, and what a seller who does not make the product should ask the supplier for. Everything was checked in October 2026 against the sources at the end of the page. Rules change, so confirm anything that affects a decision.
The short version
- CPSC's clothing storage unit rule (16 CFR part 1261, the STURDY rule) covers free-standing bedroom storage furniture that is at least 27 inches tall, weighs at least 30 pounds and has at least 3.2 cubic feet of enclosed storage. It applies to units manufactured after September 1, 2023.
- A covered unit must pass stability tests, ship with an anti-tip device and carry warning labels. CPSC's page names manufacturers and importers as the parties that certify compliance.
- EPA's formaldehyde rule (40 CFR part 770) covers hardwood plywood, medium-density fiberboard (MDF) and particleboard, including finished goods made from them. Finished goods must carry a "TSCA Title VI compliant" label.
- Retailers and distributors of composite wood goods must take reasonable precautions, which includes holding a written supplier statement of compliance and keeping records for three years.
- CPSC's upholstered furniture flammability rule (16 CFR part 1640) requires a permanent label reading "Complies with U.S. CPSC requirements for upholstered furniture flammability".
- California adds its own TB 117-2013 flammability label, and its Bureau states that responsibility rests with retailers as well as manufacturers.
- CPSC's reseller guidance says it is illegal to sell any recalled product and that resellers should not sell clothing storage units that fall short of the stability standard.
1. Three rules, three agencies
The quickest way to keep these apart is to ask what could go wrong with the product, because each agency's rule answers one of those questions.
| Hazard | Rule | Agency | Typical products |
|---|---|---|---|
| Tipping over onto a child | 16 CFR part 1261, clothing storage units | CPSC | Dressers, chests of drawers, armoires, wardrobes with drawers or hinged doors |
| Formaldehyde released by glues | 40 CFR part 770, TSCA Title VI | EPA | Anything made from hardwood plywood, MDF or particleboard |
| Fire started by a smoldering source | 16 CFR part 1640, plus California TB 117-2013 | CPSC, and California's Bureau of Household Goods and Services | Sofas, armchairs, upholstered dining chairs, children's upholstered seating |
One product can fall under more than one. A particleboard dresser with a fabric-covered drawer front, for example, is a clothing storage unit and a composite wood product at the same time. The rest of this guide takes each rule in turn and then returns to what to ask your supplier.
2. Anti-tip: the clothing storage unit rule
Where the rule comes from
Congress passed the STURDY Act in 2022. CPSC's page lists the statute as 15 U.S.C. 2056f and the final rule as 88 FR 28403, published in 2023. The rule makes the ASTM F2057-23 standard mandatory: 16 CFR 1261.2 says each unit subject to that standard must comply with it, and identifies the version as approved on February 1, 2023. CPSC states that the rule applies to clothing storage units manufactured after September 1, 2023.
Which products are covered
CPSC's business guidance defines a covered unit as free-standing furniture with drawers or hinged doors, intended for storing clothing and typical of bedroom furniture. A unit is in scope only if it meets all three thresholds:
- height of at least 27 inches;
- weight of at least 30 pounds;
- enclosed storage volume of at least 3.2 cubic feet.
CPSC's examples include chests, chests of drawers, armoires, chifferobes, bureaus, door chests and dressers, and it says fabric dressers with drawers are in scope if they meet the criteria. For the volume test, CPSC gives two formulas. For extendible elements such as drawers, volume is height (measured from one-eighth inch below the drawer bottom to the lowest obstruction) multiplied by width and depth. For non-extendible enclosed storage, such as space behind a hinged door, the volume is 50 percent of height times width times depth.
An illustrative check, using made-up dimensions: a wardrobe-style unit with hinged doors, 30 inches high, 30 inches wide and 18 inches deep, has 30 x 30 x 18 = 16,200 cubic inches. One cubic foot is 1,728 cubic inches, so that is 9.375 cubic feet. At 50 percent for non-extendible storage, the counted volume is 4.69 cubic feet, which clears the 3.2 cubic foot threshold. If it is also at least 30 pounds, it is in scope, because it is above 27 inches.
CPSC lists several exclusions: bookcases and entertainment furniture, office and dining furniture, jewelry armoires, underbed drawer units, occasional or accent furniture not for bedroom use, laundry storage and sorting units, built-in units, and clothing storage chests covered by ASTM F2598. If your product sits near a boundary, read the page rather than relying on a category name.
What a compliant unit has to do
The requirements come from ASTM F2057-23, and CPSC's page summarizes them like this.
- Interlocks. Interlocks must work without extra consumer action in normal use, and an interlocked element must hold under 30 pounds of force for five seconds in testing.
- Tip-over tests. Where more than 50 percent of the storage volume is extended, the enclosed storage is loaded at 8.5 pounds per cubic foot and held for 30 seconds. A 10 pound horizontal force is applied at the highest hand-hold, no higher than 56 inches, for 10 seconds. A carpet test places a 60 pound weight on the front door or extendible element most likely to tip the unit, for 30 seconds.
- Anti-tip device. It must meet ASTM F3096 and be packaged with the product.
- Warning labels. The unit must carry required statements and pictograms. CPSC notes that its enforcement policy accepts minor, non-substantive wording differences from the ASTM figures.
Who certifies
CPSC's guidance says manufacturers and importers must issue a certificate: a Children's Product Certificate for children's products or a General Certificate of Compliance for general-use products, citing "16 CFR part 1261 - Clothing storage units". The page does not mention retailers. That does not make a retailer immune. CPSC's Resellers Guide states that its laws and regulations apply to any person who sells, offers for sale, manufactures, distributes or imports consumer products in the United States, including thrift stores, consignment stores, charities and individuals holding yard sales.
How enforcement looks in practice
CPSC has been publishing recalls for dressers that violate the standard. One recall dated August 6, 2026 (number 26-663) covered about 2,050 dressers sold on Amazon and Wayfair at roughly $70 to $160. CPSC said they were unstable unless anchored to the wall and violated the mandatory standard for clothing storage units, and the notice describes them as violating the mandatory standard. CPSC's Resellers Guide separately says it is illegal to sell any recalled product.
Worth remembering: CPSC's Resellers Guide, published in May 2021, treated a unit within scope of ASTM F2057 that does not meet the standard as having a defect that could present a substantial product hazard, and told resellers not to sell it. It also advises checking cpsc.gov/recalls before accepting any dresser for resale.
3. Formaldehyde: the composite wood rule
What it covers
Under Title VI of the Toxic Substances Control Act, EPA regulates formaldehyde emissions from composite wood. EPA's page lists the covered products as hardwood plywood, medium-density fiberboard and particleboard, plus household and other finished goods that contain them. The standards in 40 CFR 770.10 apply to covered products sold, supplied, offered for sale or manufactured (including imported) in the United States on or after June 1, 2018, whether the product is a panel, a component part or part of a finished good.
| Product | Emission limit (parts per million formaldehyde) |
|---|---|
| Hardwood plywood, veneer core or composite core | 0.05 |
| Medium-density fiberboard (MDF) | 0.11 |
| Thin MDF | 0.13 |
| Particleboard | 0.09 |
The limits are tested to ASTM E1333-14. EPA's page says its standards are set at the same levels as California's CARB Phase II standards.
The label on a finished good
For furniture, the key section is 40 CFR 770.45(c). The fabricator must label each finished good, or each box or bundle containing them. The label must be in legible English and give the fabricator's name, the production date in month and year format, and the statement "TSCA Title VI compliant". Labels can be stamps, tags or stickers. If a finished good is not individually labeled, the importer, distributor or retailer must keep a copy of the label, be able to say which products it covers, and provide the label information on request. Importers, distributors and retailers must also leave labels intact on finished goods, including component parts sold separately.
There is a de minimis exception to the labeling requirement: finished goods that contain only a small amount of regulated composite wood, not exceeding 144 square inches based on the surface area of the largest face, are excepted from labeling, unless the item is designed to combine with others to create larger surfaces. Check that clause before assuming a modular or multi-piece kit qualifies.
What a seller who is not the maker must do
Section 770.30 says importers, fabricators, distributors and retailers must take reasonable precautions to ensure the composite wood products they sell or hold for sale comply. For fabricators, distributors and retailers, that means obtaining bills of lading, invoices or comparable documents that include a written supplier statement that the products are TSCA Title VI compliant, or were produced before June 1, 2018. Section 770.40(d) says these entities must keep the records for a minimum of three years. Importers also have to follow the customs certification rules at 19 CFR 12.118 through 12.127, which have applied since March 22, 2019.
EPA's page also reports a recent proposal: on February 6, 2026, EPA proposed updating seven voluntary consensus standards and adding ISO 12460-2:2024 as a quality control test method. That was a proposal when this guide was checked, so watch the docket (EPA-HQ-OPPT-2017-0245) rather than assuming anything has changed.
4. Flammability: federal and California labels
The federal rule
CPSC's upholstered furniture page says 16 CFR part 1640 sets smolder-resistance requirements for upholstered furniture. It follows a 2020 law and incorporates the California TB 117-2013 test methods; the June 2013 or January 2019 version of TB 117-2013 may be used. The dates are:
- Testing: items manufactured, imported or reupholstered on or after June 25, 2021.
- Labeling (section 1640.4): items manufactured, imported or reupholstered on or after June 25, 2022.
The rule covers indoor seating furniture with an upholstered seat, back or arm that is stuffed or filled, including children's furniture. Mattresses, foundations, bedding and exercise-only furniture are excluded. CPSC also lists exemptions for outdoor-only cushions and pads, certain products with half an inch of filling or less, certain children's products such as car seats and strollers, and small decorative throw pillows not intended for seating.
Each covered item needs a permanent label stating "Complies with U.S. CPSC requirements for upholstered furniture flammability." CPSC recommends at least one-eighth inch black text on a white background with a black border, in English. The label can be separate or added to the California TB 117-2013 label. A hangtag or a zip tie does not count as permanent. CPSC says no General Certificate of Conformity is required, and that the label is the manufacturer's certification. The page names manufacturers, importers and reupholsterers as the parties covered, and it does not address retailers.
California on top
California's Bureau of Household Goods and Services, in a TB 117-2013 FAQ last revised June 2019, says upholstered furniture sold in California (except exempt items) must carry a flammability label, and furniture made after January 1, 2015 must carry the TB 117-2013 label with a prescribed notice about care near open flame or burning cigarettes. The same FAQ says all upholstered furniture, including exempt furniture, must have a law label. It also says responsibility for compliance rests not only with the manufacturer but also with the importer, wholesaler, retailer or any person having the goods with the intent to sell, quoting Business and Professions Code section 19072.
CPSC's page adds that its federal label is in addition to California's flame-retardant disclosure under SB 1019. CPSC also states that states and local governments are preempted from creating or enforcing their own flammability rules for upholstered furniture, though laws on other health or safety risks are not preempted. Because the two statements can both be required for goods sold into California, ask your supplier whether the product carries both.
California chemical warnings are a separate topic, covered in our guide to Prop 65 warnings for online sellers.
5. If you dropship furniture
A dropshipper rarely sees the product before the customer does, which makes the paperwork the only protection you have. The sources above suggest what to request, product by product, before you list. Our guides on verifying a US wholesale supplier and on CPSC basics for online sellers go further on the supplier side.
| If the product is... | Ask for... |
|---|---|
| A dresser, chest or armoire at least 27 inches tall | Its Children's Product Certificate or General Certificate of Compliance citing 16 CFR part 1261, confirmation that an anti-tip device is packed in the box, and a photo of the warning label |
| Made from plywood, MDF or particleboard | A written statement that it is TSCA Title VI compliant, with the fabricator's name and production date shown on the label or packaging |
| Upholstered seating | Confirmation of the permanent CPSC compliance label and, for California sales, the TB 117-2013 label and law label |
| Imported by the supplier | Who the importer of record is, and that the customs certification for composite wood was handled |
If a supplier cannot produce these, treat the product as unverified. A weak answer on one product is also a reason to look harder at the rest of the supplier's range. Our guide on product liability and recalls looks at what a seller is responsible for when something goes wrong.
Keep the documents: the EPA rule asks for three years of records.
6. Used and secondhand furniture
Used furniture is not a loophole. CPSC's Resellers Guide says its laws apply to anyone who sells consumer products, including those who sell on auction websites, and that resellers cannot sell or donate products that do not meet the requirements of the law. It also says that although CPSC does not require resellers to test products, a hazardous, non-compliant or recalled product should be destroyed rather than sold or given away. For furniture it adds that CPSC recommends not selling broken, cracked or unstable furniture, and that furniture made before 1978 is more likely to contain lead paint hazards.
The practical routine for a used dresser is three checks: search cpsc.gov/recalls for the model, confirm that it has a working anti-tip device or a place to attach one, and check that the label survives. For a used sofa, check the label that shows its flammability compliance, and do not remove it.
7. Common mistakes
- Judging by the category name. CPSC's scope turns on height, weight and enclosed storage volume, so work through all three thresholds.
- Leaving the anti-tip hardware out of the listing photos. CPSC's rule says the device must be packaged with the product, so show it and mention it.
- Relying on a supplier's verbal assurance. The EPA rule talks about a written supplier statement.
- Forgetting California. Its Bureau states that retailers share responsibility for the flammability label.
- Ignoring recalls on old stock. CPSC says it is unlawful to offer recalled products for sale, so having one in inventory is a federal violation.
Sources and how we checked
Facts in this guide were checked against these official pages in October 2026. Rules and figures change, so confirm anything that affects a decision. This is general information, not legal or tax advice.
- Clothing Storage Units business guidance (CPSC)
- 16 CFR 1261.2: Requirements for clothing storage units (Cornell Legal Information Institute, reproducing the CFR)
- Upholstered Furniture FAQ (CPSC)
- 16 CFR 1640.4: Labeling (Cornell Legal Information Institute)
- Winston Porter and Seeday dressers recall, August 6, 2026 (CPSC)
- Resellers Guide to Selling Safer Products, May 2021 (CPSC)
- Formaldehyde Emission Standards for Composite Wood Products (EPA)
- 40 CFR 770.10: Emission standards (Cornell Legal Information Institute)
- 40 CFR 770.30: Importers, fabricators, distributors, and retailers (Cornell Legal Information Institute)
- 40 CFR 770.40: Recordkeeping (Cornell Legal Information Institute)
- 40 CFR 770.45: Labeling (Cornell Legal Information Institute)
- Technical Bulletin 117-2013 FAQs, revised June 2019 (California Bureau of Household Goods and Services)
Questions people ask
Which dressers does the CPSC anti-tip rule cover?
CPSC says a covered clothing storage unit is free-standing bedroom-type furniture with drawers or hinged doors that is at least 27 inches tall, weighs at least 30 pounds and has at least 3.2 cubic feet of enclosed storage. It applies to units manufactured after September 1, 2023.
Does a reseller need to hold a certificate for a dresser?
CPSC names manufacturers and importers as the parties who issue the certificate. CPSC's reseller guidance says its laws apply to anyone who sells consumer products and that resellers should not sell units that fail the stability standard, so asking for the certificate is sensible.
What does the formaldehyde label on furniture say?
EPA's labeling rule requires the fabricator's name, the production date in month and year format, and the statement "TSCA Title VI compliant". Retailers who sell unlabeled goods must keep a copy of the label and provide the information on request.
How long must I keep formaldehyde compliance records?
EPA's recordkeeping rule says importers, fabricators, distributors and retailers must keep the records described in section 770.30 for a minimum of three years. Those records include a written supplier statement of TSCA Title VI compliance.
Is there a federal flammability label for sofas?
Yes. CPSC's rule at 16 CFR part 1640 requires a permanent label reading "Complies with U.S. CPSC requirements for upholstered furniture flammability" on covered items manufactured, imported or reupholstered on or after June 25, 2022.
Does California have extra furniture labeling requirements?
Yes. California's Bureau of Household Goods and Services requires a TB 117-2013 flammability label and a law label on upholstered furniture sold there, and says responsibility rests with retailers as well as manufacturers. CPSC says its federal label is in addition to California's.